LENCO MARINE15064-001 Bennett Retrofit Kit - 12V
Description
⚓ Upgrade your boat’s brain with seamless 12V power!
- LIGHTWEIGHT COMPACT - At just 2.2 lbs and compact dimensions, it fits perfectly without bulk.
- BOOST YOUR BOATS IQ - Transforms your vessel with cutting-edge retrofit technology for smarter control.
- EFFORTLESS 12 V UPGRADE - Power your boat with reliable 12-volt compatibility for smooth performance.
- FUTURE PROOF YOUR RIDE - Compatible with switch kits sold separately, so you can customize as you grow.
- PLUG PLAY SIMPLICITY - Connects directly to your existing wire harness—no complex rewiring needed.
The LENCO MARINE 15064-001 Bennett Retrofit Kit is a lightweight, compact 12-volt retrofit solution designed to enhance your boat’s control system. Featuring a plug-and-play connector that integrates effortlessly with existing wire harnesses, it enables easy upgrades without rewiring. Compatible with separately sold switch kits, this kit makes modernizing your marine setup straightforward and future-ready.
Specifications
| Manufacturer | Lenco Marine |
| Brand | LENCO MARINE |
| Model | 15064-001 |
| Item Weight | 2.2 pounds |
| Product Dimensions | 14.5 x 6.75 x 4.75 inches |
| Item model number | 15064-001 |
| Is Discontinued By Manufacturer | No |
| Manufacturer Part Number | 15064-001 |
Reviews
C**S
Perfect
Just what the dr ordered. Perfect fit
Y**.
Installing lenco actuator
What iblike about it is that it was a easiest thing to do, no cutting grinding or anything else, just take the old ones out and put the new one back on, hassle free 😉
T**R
Great priced replacement for my hydraulic Bennett system
I had a Bennett hydraulic pump system on my boat that had failed. I bought this kit and it was a drop in replacement. All items required were included. Two actuators, brackets, and bolts. Some jumpers were included for wiring but I did not need them.You are required to re-use the bottom brackets that mount to the existing trim tabs, but the kit includes new retainer pins if needed.The existing hole in the transom from your fluid lines is sealed with a rubber compression gromet on the back of the upper bracket. This works well.I had an existing four wire connector on the inside where the old pump was located. Red/blue/yellow/green and a separate power/ground wire I no longer needed.I cut the pump side connector to re-use to connect directly to both the actuators (wht/blk pairs), Make sure you shrink wrap the wires to prevent corrosion.I also re-used a dual switch I had up on the dash but re-wired according to the attached diagram I found on internet.This was a fairly easy installation, the first actuator took some extra time to figure out but the second actuator installed in 5-10 minutes.One note: The kit states that your old Bennett system must be "4 ring" to work. This can be identified by how many rings are around your old actuators. Right on the cylinders there are 3 or 4 rings. I had 4 rings and it was plug and play.
B**N
Fit perfect
Easy to install
A**R
Good replacement parts
No oil to leak and works the same as originally
D**O
Parts
Best part it comes with the wrap everything’s perfect
M**R
Did not work
My mechanic installed them and they had a grinding noise he advised me to not use them there was a problem. He has installed 100's of them and never had this problem before.
S**G
Easy Retro fit
I had added Lenco Trim tabs to my last boat and was pleased with their performance. My current boat, bought used, came with Bennet hydraulic tabs. I quickly realized how much I missed my Lenco Electric tabs. The quickness and ease of adjustment of the Lenco actuators is far superior. The instructions provided for the swap were easy to follow and used the existing wire from the Bennet pump. Definitely purchase the Lenco switch panel that has light up indicators.
Common Questions
Trustpilot
1 month ago
3 weeks ago
